Oki C 5200ne Uživatelský manuál

9Changing Default Media SettingMP Tray (cont.)Then, Set the Media Type(Heavy Paper and Labels Only)1. Press .MPT MEDIATYPEPLAIN

10Loading MediaTrays 1 & 212345Media Weight RangeTray 1:16 to 32 lb. US Bond (60 to 120 g/m2)Tray 2:16 to 47 lb. US Bond (60 to 177 g/m2)Media Siz

11Loading MediaMulti-Purpose Tray123456Letterhead stationery:• Single-sided printing: load face up, top edge into the printer.• Double-sided printing:

12Selecting/UsingPaperSample Ream Label: Media Weight, US Bond (see page 5) [sometimes given as substance] Media Weight, Metric: Look for this to conf

13Selecting/UsingTransparenciesSpecificationsCaution!Transparencies must be able to withstand 446°F (230°C) for 0.2 second, including mechanical press

14Selecting/UsingLabelsSpecificationsInsert labels in the Multi-Purpose tray:• label side up• top edge aimed into the printer.Caution!Labels must be a

15Selecting/UsingThick PaperSample Ream Label: Media Weight, Index (see page 5). Media Weight, Metric: Look for this to confirm Index vs US Bond (see

16Selecting/UsingEnvelopesSpecificationsCaution!Envelopes must be able to withstand 446°F (230°C) for 0.2 second, including mechanical pressures to 25

17Selecting/UsingOki Print MediaOki® Synflex™Order # 52205901 Waterproof Tearproof White, 8½'' x 11'' (216 x 279 mm) 100 shee

18Selecting/UsingOki Media (cont.)Oki Premium Color TransparenciesOrder # 52205701 Size 8½'' x 11'' (216 x 279 mm) 50 sheets/bo

1ContentsOrdering Replacement Supplies ... 3Media Settings ...

19Printing Built-In ReportsPrinting the MenuMap (Listing of the Current Menu Settings)Note: The “…” in these steps indicates that you should keep pres

20Setting Power Save ParametersPower SavePower Save sets how long the printer waits before going into standby mode. This saves energy, but the printer

21Power Save Parameters (cont.)4. Press …POWER SAVEENABLE†5. Press .POWER SAVEDISABLE†† Pressing the + button toggles back and forth between Enable a

22Control PanelButtonsBackPress this button to go back to the previous Item or Category, or to place the printer back on line.Menu +Press MENU + to en

23Control PanelLightsReady LED (Green)On: printer is on line.Off: printer is off line.Flashing: printer is receiving data.Attention LED (Red)On: Warni

24Clearing Media JamsJam 382OPEN TOP COVER382: PAPER JAM12• If the sheet does not come out easily, go to step 3.• If the sheet does come out easily, c

25Clearing Media Jams (cont.)56

26Clearing Media Jams (cont.)Jam 381OPEN TOP COVER381: PAPER JAM123 Remove the image drums/toner cartridges:Caution!To avoid damage to the drums:• Be

27Clearing Media Jams (cont.)4567Warning! If the printer has been printing, the fuser will be HOT!To remove a sheet trapped in the fuser, grasp the ed

28Clearing Media Jams (cont.)Jams 372 & 380OPEN FRONT COVERnnn: PAPER JAMnnn = 372 or 380123

2Changing Toner Cartridges ...35Error Messages ...

29Clearing Media Jams (cont.)Jams 370, 373 & 383OPEN DUPLEX COVERnnn: PAPER JAMnnn = 370, 373, 38312oror

30Clearing Media Jams (cont.)3CAUTION! Fuser may be HOT!If the sheet is trapped in the fuser, lift the top cover, reach in and push the fuser pressure

31Clearing Media Jams (cont.)Jam 371OPEN DUPLEX COVER371: PAPER JAM1 Power off! 234567

32Clearing Media Jams (cont.)Jam 391OPEN FRONT COVER391: PAPER JAM123456

33Clearing Media Jams (cont.)Jam 392OPEN FRONT COVER392: PAPER JAM123456

34Clearing Media Jams (cont.)Jam 390CHECK MP TRAY390: PAPER JAMIf the Sheet Has Just Begun to Enter the Printer1If the Sheet Can’t Easily Be Pulled Ou

35Changing Toner CartridgesNote: Use only Type C6 Toner.REPLACE TONERnnn: XXXX* TONER EMPTY* nnn: XXXX =410: YELLOW 411: MAGENTA412: CYAN 413: BLACK1

36Changing Toner Cartridges (cont.)678910111213Important!The TONER LOW message should disappear from the display. If it doesn’t, try printing a page.

37Error MessagesSome of the more common error messages appear below. For additional error messages, see “Error Messages” under “Troubleshooting” in yo

38Error Messages (cont.)SET XXX ON MPTRAYAND PUSH ON-LINE SWITCHThe printer has received a job for printing from the Multi-Purpose Tray and no media i

3Ordering Replacement SuppliesHow to Order• Consult the dealer where you purchased your printer.•Consult an Oki Data Authorized Sales or Service Deale

39Error Messages (cont.)CHECK FUSER UNIT320: FUSER UNIT MISSINGThe fuser is not properly installed.What to DoOpen the top cover and check the fuser:1.

40Service & SupportFirst …Consult the store where you purchased your printer.Additional OKI Resources Available 24 hours a day,7 days a week• Vis

4Media SettingsWhy Change Media Settings?Improper media settings:• cause poor quality printing• cause flaking• can damage the printerDefault Media Set

5Media Settings (cont.)Media Settings for Individual Print JobsIf you are printing a job on special media, you can temporarily load the media in a tra

6Changing Default Media SettingsMedia Weight Trays 1 & 2To Change the Media Weight Default for Trays 1 & 2Note: The default media weight setti

7Changing Default Media SettingsMP TrayTo Set Transparencies as the Default Media in the MP TrayNote: For the MP Tray, the default Media Type setting

8Changing Default Media SettingsMP Tray (cont.)To Set Heavy Paper, Labels, or Envelopes as the Default Media in the MP TrayNote: For the MP Tray, the